![]() Fit the wall plugs provided or fittings as appropriate for the surface.Level using guides below the L and R symbols. Make provision for the electric supply cable and wall plugs / appropriate fittings using the main body as a template.Mark out and drill a spigot hole to suit 100mm diameter rigid ducting.Fans should not be fitted to unsupported plasterboards. When fitting fans in the ceiling, if high density plasterboard is not used, a support (min 18mm thick) should be mounted between the ceiling joists. The iCONsmart can be installed into a wall or ceiling. Using the cable clamp provided, secure the mains cable into place.Wire the fan to supply cable, referring to the electrical installation guide.Position the fan so cable entry and fitting holes align with those on the mounting surface.Pierce the grommet to allow the mains cable to be fed through while maintaining seal integrity.Fit the sealing grommet supplied into the cable entry hole. ![]() (If you have purchased a module for installation, refer to module instructions now.) These modules are available separately and can be fitted at the time of installation or retro-fitted. These include: timer module (TM) functionality that can be unlocked via a unique code (on a scratch card), humidity & timer (HT), motion sensor & timer (MST) or a combination of all three (MSHT). 3 month rolling log of power consumption, time on and flow rates recording.Commission / Notify NICEIC of installation.Bluetooth connection to your smart device.ICONsmart has several features included as standard and can also be fitted with digital micro modules to give a range of extra control options. Remove the IPX cover by undoing the screw in the centre.Note front cover position for reassembly purposes. Hold the main body, turn the front cover anticlockwise.Remove locking screw from the bottom of the front cover.Front cover iris leaves must be in the fully closed position.Ensure selected power source being used is isolated.ICONsmart comes with a newly developed flow sensing technology that automatically adjusts and maintains the set extraction flow rates when within the parameters of the fan. Switches for fans should be selected and sited in accordance with BS 7671:2018. Isolator switch, circuit breaker) with a distance greater than 3 mm between its open contacts shall be required according to BS 60669-1. The iCONsmart 15 is IPX5 rated and therefore it is suitable for mounting in bathrooms (in zone 1 and 2).įor fans mounted in zones 1 & 2 as defined in BS 7671:2018, additional protection must be provided by a Residual Current Device (RCD) not exceeding 30mA as well as having an Arc Fault Detection Device (AFDD).Ī disconnector (e.g. The iCONsmart 15 requires a 110V-240V 50/60 Hz single phase supply. Building Regulations and to the latest IET standards, or the appropriate regulations in the country of installation. Splashproof, tiling friendly, wipe clean cover.Airflow iCONsmart 15 - Extractor Fan Manual and Installation VideoĪll electrical installation must be carried out by an approved electrician in accordance with Part "P" U.K.Complies with latest Building Regulations (F1 ventilation).Unique iris shutter, prevents back draughts, operates silently and helps reduce noise ingress.Interchangeable control modules match fan to installation.The iCON15 is supplied for remote switching.Quiet, stylish, slim and unobtrusive in wall/ceilings, surface/recessed mounting.Modules include Pullcord, Timer, Humidity or Motion Sensing operation.Ĭhoice of Silver, Sandstone, Chrome & Anthracite covers However, its functionality may be enhanced through the use of optional 'snap-in' control modules which are quick to fit and wire. The Airflow iCON15 may be wired into the light switch or separate remote switch for basic on / off manual switching. The unique iris shutter, prevents backdraughts, operates silently and helps reduce noise ingress. ![]() Tiling is a breeze with the circular cover flange, reducing the need to make good. Cantilever fixing lugs enable recessed installation on uneven surfaces. The twist on/off cover requires only a single side entry fixing screw. ![]() A quick, core drilled hole enables immediate fixing of the fan. The iCON15 quiet, powerful axial fan has been designed with simplicity in mind. A great looking axial extractor fan which thanks to its eye-catching 'opening iris' shutter has become a modern design classic. Recessed into the wall or ceiling, it is stylish and unobtrusive, even in the smallest space. The Airflow iCON15 mains voltage axial fan is ideal for installation into Zone3 of toilets, en-suites, shower rooms and bathrooms.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |